Hallo,
ich hab hier eine Smart-UPS 700 per Com 1 mit dem Rechner verkabelt (Debian etch) und den apcupsd installiert.
Die USV selbst blinkt bei den Batterie-LEDs, was bedeutet daß die Laufzeit mit der verbleibenden Batterieladung kürzer als die unter "Warnzeitpunkt für schwache Batterie" angegebene Dauer (2min). Alles andere sieht normal aus: die Batterie ist voll geladen, die Last bei ca. 50%. Die USV hat vor einigen Wochen einen neuen Akku erhalten und zeigt dieses Verhalten, seit eine Last am Ausgang hängt. Eine 2. USV ebenfalls mit einem neuen Akku verhält sich genauso.
apctest bestätigt die Werte beim auslesen unter Punkt ein, bricht aber eine Laufzeitkalibrierung ab (siehe unten). powerflute kommentiert das Verhalten mit "Battery failure", multimon.cgi sagt "LOW BATTERY".
Kann mir hier jemand weiterhelfen?
~# apctest
2008-06-13 16:04:36 apctest 3.12.4 (19 August 2006) debian Checking configuration ... Attached to driver: apcsmart sharenet.type = DISABLE cable.type = CUSTOM_SMART
You are using a SMART cable type, so I'm entering SMART test mode Unknown mode.type: 11 Setting up the port ... Hello, this is the apcupsd Cable Test program. This part of apctest is for testing Smart UPSes. Please select the function you want to perform.
1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit
Select function number: 1
I am going to run through the series of queries of the UPS that are used in initializing apcupsd.
Simulating UPSlinkCheck ... Wrote: Y Got: SM Attempting to use smart_poll() ... Sent: Y Got: SM Good -- smart_poll() works!.
Going to ask for valid commands... Protocol version is: 3 Alert characters are: !$%+?=#| Command characters are: ^A^N^Z+-789>@ABCDEFGKLMNOPQRSUVWXYZ'abcefgjklmnopqrsuxyz^M
Now running through apcupsd get_UPS capabilities(). NA indicates that the feature is Not Available
UPS Status: 48 Line quality: FF Reason for last transfer to batteries: S Self-Test Status: NO Line Voltage: 235.3 Line Voltage Max: 236.6 Line Voltage Min: 232.7 Output Voltage: 235.3 Batt level percent: 100.0 Batt voltage: 27.60 UPS Load: 053.0 Line freq: 50.00 Runtime left: 0000 UPS Internal temp: 045.4 Dip switch settings: 00 Register 1: 00 Register 2: 00 Register 3: 00 Sensitivity: H Wakeup delay: 000 Sleep delay: 020 Low transfer voltage: 196 High transfer voltage: 253 Batt charge for return: 00 Alarm status: 0 Low battery shutdown level: 02 UPS Name: UPS_IDEN UPS Self test interval: 336 UPS manufacture date: 09/22/99 UPS serial number: NS9939230793 Date battery replaced: 09/22/99 Output voltage when on batteries: 230 Nominal battery voltage: 024 Percent humidity: NA Ambient temperature: NA Firmware revision: 50.11.I Number of external batteries installed: 000 Number of bad batteries installed: NA UPS model as defined by UPS: GWI UPS EPROM capabilities string: uD43132135138129uM43229234239224uA43110112114108uI43253264271280lD43103100097106lM43177172168182lA43090092081085lI43196188208204e44200155090oI43230240220225oD13115oJ13100oM13208s441HMLLq44202050710p443020180300600k4410TLNr443000060180300E443336168ON OFF The EPROM string is 253 characters long! Hours since last self test: NA
That is all for now.
1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit
Select function number: 2
First ensure that we have a good link and that the UPS is functionning normally. Simulating UPSlinkCheck ... Wrote: Y Got: SM Attempting to use smart_poll() ... Sent: Y Got: SM Good -- smart_poll() works!.
Checking estimated runtime ... Current runtime is 0 minutes Checking for battery level ... Battery level 003.0 insufficient to run test.
1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit
Select function number: 4
Monitoring the calibration progress ... To stop the calibration, enter a return.
Battery charge 100 Remaining runtime is 0 minutes ..... Battery charge 100 Remaining runtime is 0 minutes
User input. Terminating calibration ...
Attempting to abort calibration ... Response to abort request: OK
1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit
Select function number: 7
2008-06-13 18:08:02 End apctest.