Hallo, Leute!
Ich habe schon die Frage Ende September gestellt und habe reichliche Antworten bekommen.
Nun ist es soweit, daß ich das ganze einrichten soll. Und es geht nicht...
Auf dem Linux-Server ist Ubuntu 10.04 Server installiert. Der Switch ist ein Procurve 3400cl.
Hier meine Konfiguration von Linux:
/etc/network/interfaces: auto bond0 iface bond0 inet static address 192.168.1.56 network 192.168.1.0 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.13 bond-slaves none bond-miimon 100 bond-mode 802.3ad bond-lacp-rate 1
auto eth0 iface eth0 inet manual bond-master bond0 bond-primary eth0 eth1 eth2
auto eth1 iface eth1 inet manual bond-master bond0 bond-primary eth0 eth1 eth2
auto eth2 iface eth2 inet manual bond-master bond0 bond-primary eth0 eth1 eth2
/etc/modprobe.d/aliases.conf: alias bond0 bonding options mode=4 miimon=100 downdelay=200 updelay=200
Dann habe ich den Bonding gestartet. Nun sehe ich:
/proc/net/bonding/bond0: Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0
802.3ad info LACP rate: fast Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 2 Number of ports: 1 Actor Key: 9 Partner Key: 52 Partner Mac Address: 00:23:47:c0:00:80
Slave Interface: eth0 MII Status: down Link Failure Count: 0 Permanent HW addr: 00:11:0a:56:96:10 Aggregator ID: 1
Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:19:d1:41:49:c2 Aggregator ID: 2
Slave Interface: eth2 MII Status: up Link Failure Count: 3 Permanent HW addr: 00:11:0a:56:96:11 Aggregator ID: 3
Auf dem Switch (Procurve 3400cl) habe ich folgendes eingerichtet:
max-vlans 256 time timezone 120 interface 1 no lacp exit interface 2 no lacp exit interface 3 no lacp exit trunk 1-3 Trk1 LACP sntp server 83.133.123.165 sntp server 83.133.119.20 sntp server 85.31.187.67 timesync sntp sntp unicast snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 4-48,Trk1 ip address 172.16.100.1 255.240.0.0 exit spanning-tree Trk1 priority 4
Zwei Kabel sind angeschloßen. Ich pinge ständig den Server, dann probiere ich ein Kabel rauszustecken. Geht weiter... Gut!
Nun stecke ich das Kabel wieder ein. Geht nicht mehr... :(
Auf dem Switch sehe ich folgendes:
show lacp PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ---- ------- ------- ------- ------- ------- 1 Active Trk1 Up Yes Success 2 Active Trk1 Down No Success 3 Active Trk1 Blocked Yes Failure
Warum ist die Port 3 "Blocked"?
Kann jemand mir einen konkreten Beispiel geben, wie ich es einrichten soll? Ich suche in der Dokumentation und Google seit knapp 2 Stunden und verstehe nur Bahnhof...
Danke für eure Hilfe! Luca Bertoncello (lucabert@lucabert.de)